當前位置：帕斯科（山東）機器人科技有限公司>>碼垛機器人保養>>更換機器人潤滑油的其他步驟是什么What are the other steps to change the robot lubricant

更換機器人潤滑油的其他步驟是什么What are the other steps to change the robot lubricant

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質其他

所在地

在線詢價收藏產品查看聯系電話

塑料機械網采購部電話：0571-88918531QQ:2568841715

聯系方式：查看聯系方式

更新時間：2024-06-05 09:13:19瀏覽次數：319次

聯系我時，請告知來自塑料機械網

產品分類 品牌分類

  碼垛機器人保養

暫無信息

帕斯科（山東）機器人科技有限公司

經營模式：其他

商鋪產品：5條

所在地區：

詢價 給他留言

產品簡介

更換機器人潤滑油的其他步驟是什么What are the other steps to change the robot lubricant

詳細介紹

更換機器人潤滑油的其他步驟是什么What are the other steps to change the robot lubricant

更換機器人潤滑油的步驟通常包括以下幾個方面：

準備工作：首先，關閉機器人電源，并等待機器人冷卻。準備好所需的工具和材料，如新的機器人專用潤滑油、清潔布、油漏盤等。
油液排放：找到機器人的排油孔和加油孔，將油漏盤放置在排油孔下方。打開排油孔的蓋子，讓舊的潤滑油流入油漏盤中。排放完畢后，關閉排油孔。
加油：將新的機器人專用潤滑油倒入準備好的容器中，使用清潔布擦拭加油孔周圍的雜質，然后將潤滑油倒入加油孔。在加油過程中，應注意控制加油量，避免過多或過少。當潤滑油從加油孔溢出時，應停止加油，并關閉加油孔。
確認潤滑情況：加油完成后，啟動機器人，運行幾個循環，以確保潤滑油能夠充分潤滑各個部位。同時，觀察機器人是否存在潤滑不良或異常情況，如潤滑油泄漏等。

此外，還有一些注意事項需要遵守：

替換潤滑油之前，要將出油口塞子拔掉。
使用手動油槍緩慢加入潤滑油，避免使用工廠提供的壓縮空氣作為油槍的動力源，如果非要使用，壓力必須控制在一定范圍內，流量也需控制得當。
必須使用規定規格的潤滑油，使用其他潤滑油可能會損壞機器人的減速器。
更換完成后，確認沒有潤滑油從出油口流出，再將出油口塞子裝好。
為了防止滑倒事故的發生，應將機器人和地板上的油跡清除干凈。

請注意，具體的步驟和注意事項可能會因機器人的型號、品牌和制造商而有所不同。因此，在進行潤滑油更換之前，建議查閱機器人的使用說明書或咨詢制造商，以確保操作的正確性和安全性。如果不熟悉相關操作，建議聯系專業的機器人維修公司或技術人員進行操作。

The steps to change the robot oil usually include the following:

Preparation: First, turn off the power of the robot and wait for the robot to cool down completely. Prepare the tools and materials you need, such as new robot-specific lubricants, cleaning cloths, oil drain trays, etc.
Oil drain: Find the robot's oil drain hole and oil filler hole, and place the oil drain disc under the oil drain hole. Open the lid of the drain hole and allow the old lube to flow completely into the drain pan. After draining, close the drain hole.
Refueling: Pour the new robot-specific lubricant into the prepared container, use a cleaning cloth to wipe the impurities around the refueling hole, and then pour the lubricant into the refueling hole. In the process of refueling, attention should be paid to controlling the amount of refueling and avoiding too much or too little. When the lubricating oil overflows from the filler hole, the oiling should be stopped, and the filler hole should be closed.
Confirm lubrication: After refueling, start the robot and run several cycles to ensure that the lubricating oil can fully lubricate all parts. At the same time, observe whether the robot has poor lubrication or abnormal conditions, such as lubricating oil leakage.
In addition, there are some considerations to follow:

Before replacing the oil, remove the outlet plug.
Use a manual meter to add lubricating oil slowly, avoid using factory-supplied compressed air as the power source for the meter, and if you have to use it, the pressure must be controlled within a certain range, and the flow rate needs to be properly controlled.
Lubricating oil of the specified specifications must be used, and the use of other lubricating oils may damage the reducer of the robot.
After the replacement is completed, confirm that no lubricating oil is flowing out of the oil outlet, and then install the oil outlet plug.
In order to prevent slip and fall accidents, the robot and the floor should be completely cleaned of oil stains.
Please note that the specific steps and precautions may vary depending on the model, brand, and manufacturer of the robot. Therefore, before proceeding with the lubrication oil change, it is recommended to consult the robot's instruction manual or consult the manufacturer to ensure the correctness and safety of the operation. If you are not familiar with the relevant operation, it is recommended to contact a professional robot repair company or technician for operation.